Our Training Courses

Work Safely at Heights (WaH)

This unit describes a participant’s skills and knowledge required to work safety at heights in the Resources and Infrastructure Industries.

This unit it appropriate for those working in operational roles where they are required to perform work at heights.

Licensing, legislative, regulatory and certification requirements that apply to this unit can vary between states, territories, and Industry sectors. Relevant information must be sourced prior to application of the unit.

Enter & Work in Confined Spaces (CS)

This unit describes a participant’s skills and knowledge required to enter and work in confined spaces in the Resources and Infrastructure Industries

This unit is appropriate for those working in operational roles undertaking work in confined spaces.

Licensing, legislative, regulatory and certification requirements that apply to this unit can vary between states, territories, and Industry sectors. Relevant information must be sourced prior to application of the unit.

Conduct Skid Steer Loader Operations Using Attachments (SS)

This unit describes a participant’s skills and knowledge required to conduct operations with skid steer loaders using attachments in Coal and Metalliferous mining and Extractive.

This unit is appropriate for those working in operational roles.

Licensing, legislative, regulatory and certification requirements that apply to this unit can vary between states, territories, and Industry sectors. Relevant information must be sourced prior to application of the unit.

Licence to Operate a Boom-type Elevating Work Platform (WP)

This unit specifies the outcomes required to operate a boom-type elevating work platform (boom length 11 metres or more) for licensing purposes, and involves the operation of a telescoping device, hinged device, or articulated device or any combination of these used to support a platform on which personnel, equipment and materials may be elevated to perform work. The 11 metre boom length shall be taken to mean the greater of the following:

(a) The vertical distance from the floor of the platform to the surface supporting the elevating work platform with the platform at its maximum height;
or

(b) The nominal reach, measured horizontally from the centre point of rotation to the outer edge of the platform in its most extended position.

This unit requires the operator to plan the work, conduct routine checks, set up elevating work platform, operate elevating work platform and shut down and secure elevating work platform.

TThis unit is based on the requirements of the National Standard for Licensing Persons Performing High Risk Work.

This unit in its current form meets state and territory licensing requirements. Any alteration will result in a unit which is not acceptable to regulators for the purpose of licensing.

Licence to Perform Dogging (DG)

This unit specifies the outcomes required to perform slinging techniques, including the selection and inspection of lifting gear and/or the directing of the crane operator in the movement of the load when the load is out of view of the crane/ operator for licensing purposes.

Application of the unit

This unit covers the scope of work to demonstrate competency in the application of slinging techniques, selection and inspection of lifting gear and/or the directing of the crane/ operator in the movement of the load.

This unit in its current form meets state and territory licensing requirements. Any alteration will result in a unit which is not acceptable to regulators for the purpose of licensing.

Licence to perform Rigging, Basic Level (RB)

This unit specifies the outcomes required to perform basic rigging work associated with movement of plant and equipment, steel erections, hoists (including mast climbing hoists), placement of pre-cast concrete, safety nets and static lines, perimeter safety screens and shutters; and cantilever crane loading platforms for licensing purposes.

Application of the unit

This unit requires the applicant to be able plan the work, select and inspect equipment, set up task, erect structures and plant and dismantle structures and plant.

This unit is based upon the National Standard for Licensing Persons Performing High Risk Work.

This unit in its current form meets state and territory licensing requirements. Any alteration will result in a unit which is not acceptable to regulators for the purpose of licensing.

This unit has a pre-requisite requirement. This requirement may be met by either the successful completion of the unit CPCCLDG3001A Licence to perform dogging or holding a valid licence for dogging.

Licence to operate a slewing mobile crane, <60t (C6)

This unit specifies the skills and knowledge required to safely operate a slewing mobile crane with a capacity up to 60 tonnes.

Slewing mobile crane means a mobile crane incorporating a boom or jib that can be slewed, but does not include:

  • a backhoe or
  • an excavator or
  • a front-end loader or
  • other earth moving equipment, when configured for crane operation.

This unit applies to the activities of a person operating a slewing mobile crane with a capacity up to 60 tonnes that is a:

  • non-slewing mobile crane with a capacity exceeding 3 tonnes
  • reach stacker
  • slewing mobile crane with a capacity of 60 tonnes or less
  • vehicle loading crane with a capacity of 10 metre tonnes or more, excluding the application of load estimation and slinging techniques to move a load.

A person performing this work is required to hold a slewing mobile crane with a capacity up to 60 tonnes high risk work (HRW) licence.

This unit requires a person operating a slewing mobile crane with a capacity up to 60 tonnes crane to plan work, conduct routine checks, set up crane, transfer load, mobile load and shut down and secure crane after operation.

Licensing/Regulatory Information

This unit is based on the licensing requirements of Part 4.5 of the Model Work Health and Safety (WHS) Regulations, HRW and meets Commonwealth, state and territory HRW licensing requirements.

Any alteration to this unit would result in a unit that would not be acceptable to work health and safety (WHS)/occupational health and safety (OHS) regulators for the purpose of licensing.

Licence to erect, alter and dismantle scaffolding, basic level (SB)

This unit specifies the outcomes required to erect, alter and dismantle scaffolding at the basic level, consisting of scaffolding work connected with the operation or use of modular or pre-fabricated scaffolds, cantilevered materials hoists with a maximum working load of 500kg, ropes and gin wheels, safety nets and static lines, and bracket scaffolds (tank and formwork) for licensing purposes.

Application of the unit

TThis unit covers the scope of work to plan the job, select and inspect equipment, set up task, erect scaffold and scaffold equipment and dismantle scaffold and scaffold equipment.

This unit is based upon the National Standard for Licensing Persons Performing High Risk Work.

This unit in its current form it state and territory licensing requirements. Any alteration will result in a unit which is not acceptable to regulators for the purpose of licensing.

Conduct Hydraulic Excavator Operations (EX)

This unit describes a participant’s skills and knowledge required to conduct hydraulic excavator operations in Coal and Metalliferous mining and Extractive.

This unit is appropriate for those working in operational roles.

Licensing, legislative, regulatory and certification requirements that apply to this unit can vary between states, territories, and Industry sectors. Relevant information must be sourced prior to application of the unit.

Licence to Operate a Forklift Truck (LF)

This unit specifies the skills and knowledge required to operate a forklift truck safely.

Forklift truck means a powered industrial truck equipped with lifting media made up of a mast and an elevating load carriage to which is attached a pair of fork arms or other arms that can be raised 900 mm or more above the ground, but does not include a pedestrian-operated truck or a pallet truck.

A person performing this work is required to hold a forklift truck high risk work (HRW) licence.

This unit requires a person operating a forklift truck to plan the work, conduct routine checks on a forklift truck, shift loads in a safe manner, and safely shut down and secure equipment after completing operations.

Licensing/Regulatory Information

This unit is based on the licensing requirements of Part 4.5 of the Model Work Health and Safety (WHS) Regulations, HRW and meets Commonwealth, state and territory HRW licensing requirements.

Any alteration to this unit would result in a unit that would not be acceptable to work health and safety (WHS)/occupational health and safety (OHS) regulators for the purpose of licensing.

Operate Roller/Compactor (R)

This unit describes a participant’s skills and knowledge required to operate roller/compactors in Coal and Metalliferous mining and Extractive.

This unit is appropriate for those working in operational roles.

Licensing, legislative, regulatory and certification requirements that apply to this unit can vary between states, territories, and Industry sectors. Relevant information must be sourced prior to application of the unit.

Book Now, Train Tomorrow